![behringer x32 producer downloads behringer x32 producer downloads](https://i.ebayimg.com/images/g/yZwAAOSwjThdlEP1/s-l640.jpg)
Any adjustment on the fader would affect the level sent to the sends. In this instance you would leave all of your channel faders at unity and they would act as masters for that send. Post Fader – This is used when you are feeding monitors from a dedicated monitor mixing console. This would be used if wanted to feed the bus after the dynamics section but before the Fader. Pre Fader – This send is after the Dynamics section but before the Fader. This way you can use the dynamics for your FOH mix without reducing your gain before feedback in the monitor. This is recommended for Mixbuses feeding floor monitors when you are mixing monitors from FOH. Post EQ – After the channel EQ but before the dynamics. Pre EQ – Before the EQ but after the Gate/Expander Input – Directly after the preamp and high pass filter The sends can be set up in 6 different ways similar to how the sends to the X-USB card is set up. Like the previous tabs, the Sends Tab shows the send of the selected channel, in this case it is still Channel 2/Kick Out. The Sends Tab shows and configures the Mixbuses/Aux Sends. Each band has it’s own bypass/activate button unlike the console where there is only the global active or bypass. You can also grab and drag the circles on the screen that correspond to the eq frequencies and drag the frequency higher or lower or drag the gain higher or lower. The mode for each band of the eq has a drop down menu to select the different modes available.
![behringer x32 producer downloads behringer x32 producer downloads](https://electric-shades.com/images/496880.jpg)
The button directly below that will activate or bypass the high pass filter. Selecting the “EQ” button right above the high pass filter will bypass or activate the eq. The Equalizer Tab gives an overview of the Equalizer and the High Pass/Low Cut filter. There is also a button to activate auto-release for the compressor. On the X32 console you would have to page up and down at the bottom of the Dynamics tab to see all of the controls and probably would miss or forget about some of the controls like the Mix level. All of the controls for the dynamics section are shown, and like the gate tab they are all available at once. There is an Active/Bypass button like the gate. The Dynamics Tab shows the channel’s dynamics section. An Active/Bypass is highlighted when the gate is active and we can see and control all of the aspects of the gate laid out on this one page. The Gate Tab shows the settings for the Gate. The Config Tab shows information about the pre-amp, source, and insert of a channel. This makes it easy to see how the channel is setup and shows all of the information you would need for an individual channel. Notice channel 2 “Kick Out” is highlighted. Selecting the Channel Tab gives us a more in depth overview of one individual channel. This view shows an overview of the individual channel settings, sends, dynamics, eq, and pan. Notice the Top left corner where “ Mixer” tab is selected. When you open the program you get an overview of the mixer. This is where you can find firmware downloads as well.
![behringer x32 producer downloads behringer x32 producer downloads](https://static.bhphoto.com/images/fb/969898.jpg)
Behringer x32 producer downloads software#
To download the X32 Edit software go to this Link:įind the version to download in the software dropdown menu on the right side of the webpage. Much of this information applies to the console as well so it is good to understand. The more recent versions are visually cleaner and more appealing, but not laid out in the same way as the console. The earlier version of the software was better for this because it was laid out the same as the console. The most easily overlooked use for the X32 Edit software is as a tool to learn your way around the console when you need to figure something out and you don’t have the console in front of you. They all can be controlled by a computer setup remotely and not requiring a router. This would be most useful with the X32 Rack version, Core version, or Behringer’s line of XAir mixers. The third use for the software can be remotely controlling a console. The 2nd use is that you can create presets for channels, routing, and effects that you can use when you build Scenes in the future. The most obvious is setting up Scene Files that you can load on a USB drive and then load on the console when you are onsite so you don’t have to start from scratch when you are at the gig.
Behringer x32 producer downloads free#
X32 Edit is a free download from the Behringer site and is helpful for a few different reasons. ***X32 Edit Version 4.3 is now available and includes bug fixes and support for DCA Spill in firmware 4.04*** Cymatics keys install.***A downloadable/printable version of this guide is now available in the downloads section of the website***